Local water treatment service

Water Treatment in Pinellas Park, FL

Free in-home water testing and straight answers for hard water, stains, odor, sediment, and whole-house filtration in Pinellas Park.

217 ppm
Hardness, county average — the county’s own softener setting is 11.1–14.3 grains per gallon. Pinellas Park publishes no separate drinking-water numbers of its own — this county report describes your tap
3.8 ppm
Chloramine — 95 percent of the 4.0 legal cap
41.6 ppb
Total trihalomethanes — against a limit of 80
0.8 ppb
Lead, 90th percentile — against an action level of 15

Pinellas County Utilities 2025 report — Pinellas Park’s supply, and the system behind the county’s boil-water notices for the city. Every figure is sourced in full below.

Whole-house softener and filtration setup with digital control heads — the kind of owner-installed system Aqua Pro fits in Pinellas Park homes
Real install · No stock photosWhole-house softener plus filtration with digital control heads.

What Pinellas Park water looks like

Pinellas Park’s drinking water comes from Pinellas County Utilities, the county system — the county’s own maintenance coverage lists Pinellas Park among its affected customers, and the county’s boil-water page is where a Pinellas Park notice appears when one is issued. Pinellas Park publishes no separate drinking-water numbers of its own in the records checked for this page, so the report that describes a Pinellas Park tap is the county’s report — and its numbers are worth reading plainly.

Start with hardness. The county’s own 2025 Consumer Confidence Report (CCR — the annual water quality report every public utility must publish) puts average hardness at 217 parts per million, ranging from 189 to 244 — and the county itself prints the softener setting for it: 11.1 to 14.3 grains per gallon. On the federal scale, anything over 180 parts per million is “very hard.” That is the crust on your faucets, the spots on your glass, and the scale building inside your water heater, in the utility’s own numbers.

The disinfectant runs close to its cap. Chloramine — chlorine combined with ammonia, used because it lasts longer in the pipes — hit a highest running annual average of 3.8 parts per million against a legal cap (the maximum residual disinfectant level) of 4.0: 95 percent of the cap. The byproducts that form when chloramine reacts with natural organic matter stayed around half their limits: total trihalomethanes (TTHM) at 41.6 parts per billion against a limit of 80, and haloacetic acids (HAA5) at 28.1 against a limit of 60. Chloramine matters for equipment, too: it is hard on standard softener resin, and a softener alone does not remove it — that job needs catalytic carbon with enough contact time, ahead of the softener. Twice a year, for about three weeks each time in spring and fall, the county also switches temporarily from chloramine to straight chlorine for system maintenance — Pinellas Park was among the customers listed for the fall 2026 switch (September 21 to October 10) — and taste and odor complaints spike while it lasts.

What is not the story here: lead, copper, and PFAS (per- and polyfluoroalkyl substances, the “forever chemicals”). The county’s 90th-percentile lead reading — the level 9 out of 10 sampled homes tested at or below — is 0.8 parts per billion against an action level of 15, and copper is 0.3 parts per million against an action level of 1.3 (both from 2023 tap sampling). In federal monitoring under the Fifth Unregulated Contaminant Monitoring Rule (UCMR 5), none of the 29 PFAS compounds tested was detected at the county system’s entry points — against legal limits of 4.0 parts per trillion each for the two main compounds, PFOA and PFOS. And if you have heard the fluoride question: the county stopped adding fluoride on July 1, 2025 under new state law; a natural background of 0.15 to 0.50 parts per million remains. I will tell you when a number is fine, not just when it is not.

Pinellas Park also had its own local event this year: a precautionary boil-water notice on June 17 to 19, 2026, after a water-main break, lifted after testing confirmed the water met standards. That is an infrastructure precaution after a break, not a treatment failure — and it is the county system’s notice, which is one more sign of whose water this is. The honest gap on this page: no Pinellas Park–specific distribution sampling is published in the records checked here, so every figure above is a county-system figure, presented as the supply it is. Your tap is one home on that system, with its own pipes and its own water heater. The free 20-minute test covers hardness, iron, chlorine, pH (a measure of acidity), sulfur, and total dissolved solids (TDS) at your tap. The full county table is laid out in the Pinellas County water quality results.

Sources

Your tap, not the system average

See what Pinellas Park water is doing in your home.

The free test takes about 20 minutes at your tap. No obligation and no sales pitch — just your numbers, explained against the legal limits.

How we help in Pinellas Park

Licensed & Insured · Locally owned · Owner-installed

Start with the free test

Every recommendation follows a 20-minute test at your tap — never a sales pitch.

Step one · 60 seconds

The quick water check

Answer a few questions about what your water is doing at home.

Take the 60-second water check
Step two · 20 minutes

The free test at your tap

Hardness, iron, chlorine, pH, sulfur, and total dissolved solids — measured at your home, explained on the spot.

Book your free test

Find Out What’s in Your Water—Free.

Pick a callback time. We’ll call you back as soon as possible during business hours.

Licensed & Insured · Locally owned · Owner-installed

No obligation and no sales pitch. The test takes about 20 minutes at your tap.